Every agarose gel needs a running buffer, and the two common choices are TAE and TBE. They look almost the same on the bench, but they behave differently once the current is on. This guide explains the real differences so you can pick the right buffer for your fragment size, run time and downstream steps.
TAE vs TBE at a glance
| Feature | TAE (Tris-acetate-EDTA) | TBE (Tris-borate-EDTA) |
|---|---|---|
| Best for | Large DNA fragments (roughly above 10 kb), gel extraction | Small fragments (below about 1 kb), polyacrylamide gels |
| Buffering capacity | Lower; can become exhausted in long runs | Higher; holds up better for long or high-voltage runs |
| Band sharpness | Good for large fragments | Sharper bands for small fragments |
| Migration speed | Linear double-stranded DNA runs faster | Slower |
| Downstream enzymes | Compatible with ligation and most enzymatic steps | Borate can inhibit some enzymes such as ligases |
| Typical pH of our stock | 8.0 | 8.3 |
When to choose TAE
Choose TAE when you plan to cut a band out of the gel and use the DNA for cloning, ligation or sequencing. Acetate does not interfere with most enzymes, so the recovered DNA is easier to use. TAE is also the usual choice for large fragments such as plasmids, genomic DNA digests and long PCR products, because it separates big molecules well and runs them faster. The trade-off is lower buffering capacity, so for a long or high-voltage run, recirculate the buffer or use a fresh tank.
Laboes.com stocks both the ready-to-use TAE buffer (1×), pH 8.0 and the concentrated TAE buffer (10×), pH 8.0, each in 500 mL bottles.
When to choose TBE
Choose TBE when you need sharp bands for small fragments, such as PCR products under 1 kb, restriction digest checks, or small RNA and oligonucleotide work. Its higher buffering capacity also makes it the better option for long runs and higher voltages, and it is the standard buffer for polyacrylamide gels. The trade-off is that borate can inhibit some enzymes, so purify DNA carefully if you plan to use it in ligation or other enzymatic reactions after running it in TBE.
We offer TBE buffer (10×), pH 8.3 in 500 mL bottles. Dilute it 1:10 with water to make a 1× working solution.
Ready-to-use or 10× stock?
A 1× buffer saves time: pour it straight into the tank and use it to make the gel. A 10× stock is more economical and takes up less shelf and freezer space. One 500 mL bottle of 10× makes 5 L of 1× buffer, so a case of 10 bottles makes 50 L. At the time of writing, the 1× TAE case is listed at $51.60 and the 10× TAE and TBE cases at $141.59 each. For high-throughput labs and teaching labs that run many gels, the 10× stock usually works out cheaper per liter.
Practical tips for better gels
- Use the same buffer in the gel and the tank. Mixing buffers changes the ionic strength and can distort or smear bands.
- Do not reuse running buffer indefinitely. It loses buffering capacity and its pH drifts, especially TAE.
- Keep the buffer level just above the gel. Too much buffer lowers the current through the gel and slows the run.
- Dilute stocks with clean water. If your downstream work is sensitive, use nuclease-free water to make up working solutions.
- Match the run to the buffer. If bands look smeared in a long TAE run, switch to TBE or lower the voltage.
Frequently asked questions
Can I use TAE and TBE interchangeably?
For a quick check gel, either works. For best results, match the buffer to your fragment size and downstream steps: TAE for large fragments and gel extraction, TBE for small fragments and long runs.
Which buffer is better for gel extraction and cloning?
TAE, because acetate does not inhibit most enzymes used in ligation and other downstream reactions.
Why are my bands fuzzy in TBE?
Check that the gel and the tank contain the same buffer at the same concentration, and that the voltage is not too high. Too much heat can blur bands.
How do I dilute 10× TAE or TBE to 1×?
Mix 1 part 10× stock with 9 parts water. For example, add 100 mL of 10× stock to 900 mL of water to make 1 L of 1× buffer.
Does the pH of TAE or TBE matter?
Yes. Use the stock at its stated pH (TAE pH 8.0 and TBE pH 8.3 here) and do not adjust it, because small pH changes can shift DNA migration and band sharpness.
Need electrophoresis buffers for your lab? Browse the TAE and TBE options in our catalog, or contact support@laboes.com for bulk pricing. Free shipping on orders over $1,000.
